Cinema Display VESA Mount Adapter Kit

Cinema Display VESA Mount Adapter Kit

Customer Reviews and Ratings

3.5 out of 5 stars

Based on 35 reviews

Write a Review
  • 5.0 out of 5 stars

    VESA Mount Adapter Kit

    • Written by from Roswell

    Nice quality mount, I'm extremely pleased with it, same metal texture as the Cinema Display. Kit comes with 2 sets of plastic bumpers (one for 20-23" Display and one for 30" Display), Screws, and instructions.
    I mounted my 23" Cinema Display HD to a VESA drafting table monitor arm within 10 minutes using 100mm screws (that came with the monitor arm) with no problems. I'm unsure of the difficulty to re-attach the monitor to the original stand, but it looks as straight forward as the installation of the adapter.
    If you have a Cinema Display HD and want to mount it to the wall or a desk arm, this is what you need.

    Was this useful?

    Flag as inappropriate

  • 4.0 out of 5 stars

    Strong and well engineered, but the instructions are flawed.

    • Written by from Chatsworth

    One picture in the instructions shows the attaching bar going in backwards. It won't work unless the screws go into the side that has the counter-sinks.

    0 of 1 people found this useful

    Was this useful?

    Flag as inappropriate

  • 1.0 out of 5 stars

    Not apple worthy, hated attaching it

    • Written by from Istanbul

    remove the top and bottom rubber strips for proper attachment (even then mine was touching the back of the monitor.

    0 of 5 people found this useful

    Was this useful?

    Flag as inappropriate

  • 1.0 out of 5 stars

    not apple experience worthy

    • Written by from Benton Harbor

    My coworker wanted a standing desk so I attached this for him. The amount of force I had to use to line up the screws was insane. The piece of plastic you get to unlatch the thing is cheap. Too much pressure in the wrong place and you make it useless.
    After being sick of the standing desk my coworker wanted the original stand back. I pulled it out and they needed help. They got it removed and the other stand attached, but couldn't get the monitor to tilt back. There are no instructions in the manual on removing it. I found a few things online (nothing on the apple site) but nothing was useful.
    The real trick was pushing the monitor so far forward you felt like you were breaking the thing. Then you can use the card to push the spring and release the lock. Very unfriendly.

    Get this if you need it, but be prepared for a struggle.

    7 of 9 people found this useful

    Was this useful?

    Flag as inappropriate

  • 3.0 out of 5 stars

    Nice looking... but

    • Written by from Houston

    The VESA mount looks great and works as advertised, but it is extreamly difficult to mount. It took me a good half an hour of fiddling with the screws before I got them to catch on both sides. A little more tolorance in the design would be a great benefit.

    8 of 12 people found this useful

    Was this useful?

    Flag as inappropriate

  • 1.0 out of 5 stars

    Mine didn't fit

    • Written by from Saint Joseph

    On my mid-2011 27" iMac, the holes didn't line up, and they were off a lot. I removed the protective plastic strips and it was closer, but still no fit. To make it work, I had to machine off almost 5/64" from the bracket. You should also be careful with the eight screws that hold the bar onto the back of the iMac---they're softer than you might expect. Overall, poor design or quality control (I don't know which), but I expected better from Apple.

    21 of 65 people found this useful

    Was this useful?

    Flag as inappropriate

  • 2.0 out of 5 stars

    Frankenstein contraption, total pain to install, dodgy alignment

    • Written by from Athens

    I had to return the first one of these I bought because the milling was so bad that no matter how tight I screwed it on, the screws would never align on the sides. The adapter depends on the threads of one small bolt to pull the heavily-sprung mount out of the display and into alignment. The alignment has to be perfect to install the side bolts, there is no margin for error. What a headache.

    7 of 13 people found this useful

    Was this useful?

    Flag as inappropriate

  • 4.0 out of 5 stars

    Great product but make sure you have the right monitor!

    • Written by from San Jose

    This is for the 20", 23", and 30" aluminum non-glossy monitors! This will not work for the new 24" and 27" glossy black bezel displays, so make sure you buy the right one. Search for the other VESA mount adapter kit, part #MC772ZM/A

    117 of 118 people found this useful

    Was this useful?

    Flag as inappropriate

  • 4.0 out of 5 stars

    re review by CW

    • Written by from Evergreen

    He is correct in his statements regarding detaching the desk base. After struggling with ithe card ala the instruction book with the screen upright and getting no joy, I managed to get into the Genius bar at Asspen Grove in Colorado with only an hour's notice where fiddling to get the card to contact the switch proved to be just as futile. The Tech then laid the monitor/cpu face down on the desk with the card inserted and - Whee! - the mount with the eight screws popped up and locked. Problem solved. The unit is very heavy - two people are almost a necessity, but is extremely stable and does drop the screen down a good three inches. Much easier on my nexk

    10 of 12 people found this useful

    Was this useful?

    Flag as inappropriate

  • 5.0 out of 5 stars

    Review before installing!

    • Written by from Villa Park

    A word of caution. The directions for this product are not very clear regarding the removal of thebase stand.

    The direction state you must tilt the screen all the way forward, use the provided card to depress the inner switch, and while the inner switch is depressed you are able to pull the base stand out of the imac/display. The base stand will still be connected to a spring load holder which is connected to the inside the iMac/display but will now be protruding out from the iMac/display. This spring loaded arm holder is what you will connect your vesa mount to after removing the stand that is connected to it.

    IT IS CRITICAL THAT YOU MAKE SURE THE SPRING LOADED ARM HOLDER PROTRUDES OUT OF THE IMAC/DISPLAY AND LOCKS INTO THAT POSITION BEFORE REMOVING THE BASE STAND. YOU WILL KNOW THAT IT IS LOCKED WHEN YOU REMOVE THE CARD USED TO DEPRESS THE SWITCH AND THE BASE STAND CANNOT SWIVEL BACK AND FOURTH. IF YOU FAIL TO EXTERNALLY LOCK THE SPRING LOADED ARM HOLDER AFTER YOU UNSCREW THE BASE STAND FROM THE ARM HOLDER, THE ARM HOLDER WILL DEPRESS BACK INSIDE THE IMAC/DISPLAY AND IT IS NEAR IMPOSSIBLE TO PULL BACK OUT. (IF THIS HAPPENS, YOU WILL HAVE TO BRING YOUR IMAC/DISPLAY TO THE NEAREST APPLE STORE AND HOPE THEY HAVE THE PROPER TOOL TO PULL THE INNER ARM HOLDER BACK OUT. THIS IS NO EASY TASK, EVEN FOR THE APPLE "GENIUSES."

    If you are successful and the inner spring loaded arm holder externally locks into place, installation is very simple.

    35 of 37 people found this useful

    Was this useful?

    Flag as inappropriate

  • 5.0 out of 5 stars

    Vesa Apple Display mount

    • Written by from South Walpole

    Awesome!!! very easy to install. Torx tool broke but that was minor for me. for I have my own tools. maybe problem for some one else. but ultimately very easy to install

    19 of 27 people found this useful

    Was this useful?

    Flag as inappropriate

  • 1.0 out of 5 stars

    Extremely Difficult

    • Written by from Washington Township

    I am a very handy person. I am in the process of renovation my whole house and this was the hardest task to date. The directions are not easy to follow and I wasn't sure if I am supposed to mount directly to the wall or to another wall mount. I decided to go directly to the wall. It was extremely difficult to get the holes to line up and my hand could fit behind the MAC to tighten the screws. It took me 2 days to work up a solution, but I finally did and now I am happy. For such a smart company, this is the worst design. I was very angry and frustrated until it was finally done.

    23 of 146 people found this useful

    Was this useful?

    Flag as inappropriate

  • 5.0 out of 5 stars

    Simply Perfect !!!

    • Written by from Ridgewood

    This piece is exactly what is meant to be. Installation is as described, perfect fit with VESA mounts. I read all the other reviews before and I think that people that are not happy with this adaptor, either bought a cheap mount or have no idea or talent for this kind of stuff. Any TV, monitor, etc. don't have screws holes to accommodate different dimensions or standards; the mount always comes with a bunch of screws, mounting plates and washers. The only thing I could comment is that it could come with my 30" display for the price i paid.

    23 of 31 people found this useful

    Was this useful?

    Flag as inappropriate

  • 5.0 out of 5 stars

    Great!

    • Written by from LAS VEGAS

    I'm using the Ergotron LX Desk Mount Arm - mounting kit ( 45-179-195 ) and this works great with it. If you want to make sure you get the right arm, try this Ergotron!

    10 of 12 people found this useful

    Was this useful?

    Flag as inappropriate

  • 5.0 out of 5 stars

    Perfect

    • Written by from Las Vegas

    designed perfectly, worked perfectly for 30" cinema dispaly

    4 of 4 people found this useful

    Was this useful?

    Flag as inappropriate

  • 3.0 out of 5 stars

    READ THESE REVIEWS !!!

    • Written by from Tinton Falls

    A very useful, necessary item if you plan on mounting the 24" iMac. DONT KID AROUND WITH THE TORX SCREWS, they are soft, torqued down in the factory and easily stripped! Get a good driver with alot of leverage before attempting to turn these crews, under no circumstances use the tool in the kit.

    I had to drill one out and I thought I was being careful. Why they didn't send a new set of screws with this kit is unexplainable. That being said, once on, it makes mounting a cinch.

    89 of 95 people found this useful

    Was this useful?

    Flag as inappropriate

  • 4.0 out of 5 stars

    good but

    • Written by from Prague, CZ

    can also confirm - rubber bumpers should be removed before you can attach this (at least to 20" cinema). after the procedure you may try to put one rubber back. there's no space for two.

    btw, why don't apple just make a vesa 100x100 available from the box, like all other monitor vendors do? think different?

    55 of 65 people found this useful

    Was this useful?

    Flag as inappropriate

  • 5.0 out of 5 stars

    Super Easy

    • Written by from LAKEWOOD

    I was a little worried with suspending my 30" cinema display 6 feet off the floor on an articulating arm, but the VESA mount adapter kit proved super easy and sturdy. It took all of 5 min to install. I would highly recommend this product to anyone interested.

    62 of 76 people found this useful

    Was this useful?

    Flag as inappropriate

  • 4.0 out of 5 stars

    Works great - less filling

    • Written by from San Francisco

    I had absolutely no trouble attaching the adapter to my 20" Cinema display, and absolutely no trouble attaching my articulating arm to the adapter. My only gripe is that the adapter bracket obscures part of the Apple logo on the back of the Cinema display.

    11 of 22 people found this useful

    Was this useful?

    Flag as inappropriate

  • 1.0 out of 5 stars

    Procede with caution

    • Written by from Northridge

    The tolerances are way too tight. I had to remove one of the "rubber bumpers" in order to attach this to my 23 inch display, attach it, and then pound the rubber bumper back in.

    Rookie design mistakes, I expect better from Apple. Much better.

    181 of 358 people found this useful

    Was this useful?

    Flag as inappropriate